Using the XBee Library Part 2

/*
XBee RX test for a Arduino Mega2560 using Serial3 as the XBee serial
input for a Series 2 XBee.  I took Andrew Rapp's receive example and modified
it heavily.

I wanted to experiment with and better understand how to use his XBee
library for an actual project.  With the inclusion of support for SoftwareSerial
so that the XBee can be put on digital pins leaving the Arduino serial port
available for debugging and status, the library's usefullness shot way up.  These
changes also allow for the use of the additional serial ports on a Mega2560

This is a HEAVILY commented example of how to grab a receive packet off the
air and do something with it using series 2 XBees.  This example also supports
a remote XBee end device sending analog data.  Series 1 XBees are left as an
exercise for the student.
*/

#include <XBee.h>

XBee xbee = XBee();
XBeeResponse response = XBeeResponse();
// create reusable response objects for responses we expect to handle
ZBRxResponse rx = ZBRxResponse();
ZBRxIoSampleResponse ioSample = ZBRxIoSampleResponse();

void setup() {
  // start serial
  Serial.begin(9600);
  // and the third serial port
  Serial3.begin(9600);
  // now that they are started, hook the XBee into
  // the third serial port
  xbee.setSerial(Serial3);
  // I think this is the only line actually left over
  // from Andrew's original example
  Serial.println("starting up yo!");
}

void loop() {
    // doing the read without a timer makes it non-blocking, so
    // you can do other stuff in loop() as well.
    xbee.readPacket();
    // so the read above will set the available up to
    // work when you check it.
    if (xbee.getResponse().isAvailable()) {
      // got something
      // I commented out the printing of the entire frame, but
      // left the code in place in case you want to see it for
      // debugging or something.  The actual code is down below.
      //showFrameData();
      Serial.print("Frame Type is ");
      // Andrew calls the frame type ApiId, it's the first byte
      // of the frame specific data in the packet.
      Serial.println(xbee.getResponse().getApiId(), HEX);
   
      if (xbee.getResponse().getApiId() == ZB_RX_RESPONSE) {
        // got a zb rx packet, the kind this code is looking for
     
        // now that you know it's a receive packet
        // fill in the values
        xbee.getResponse().getZBRxResponse(rx);
     
        // this is how you get the 64 bit address out of
        // the incoming packet so you know which device
        // it came from
        Serial.print("Got an rx packet from: ");
        XBeeAddress64 senderLongAddress = rx.getRemoteAddress64();
        print32Bits(senderLongAddress.getMsb());
        Serial.print(" ");
        print32Bits(senderLongAddress.getLsb());
     
        // this is how to get the sender's
        // 16 bit address and show it
        uint16_t senderShortAddress = rx.getRemoteAddress16();
        Serial.print(" (");
        print16Bits(senderShortAddress);
        Serial.println(")");
     
        // The option byte is a bit field
        if (rx.getOption() & ZB_PACKET_ACKNOWLEDGED)
            // the sender got an ACK
          Serial.println("packet acknowledged");
        if (rx.getOption() & ZB_BROADCAST_PACKET)
          // This was a broadcast packet
          Serial.println("broadcast Packet");
       
        Serial.print("checksum is ");
        Serial.println(rx.getChecksum(), HEX);
     
        // this is the packet length
        Serial.print("packet length is ");
        Serial.print(rx.getPacketLength(), DEC);
     
        // this is the payload length, probably
        // what you actually want to use
        Serial.print(", data payload length is ");
        Serial.println(rx.getDataLength(),DEC);
     
        // this is the actual data you sent
        Serial.println("Received Data: ");
        for (int i = 0; i < rx.getDataLength(); i++) {
          print8Bits(rx.getData()[i]);
          Serial.print(' ');
        }
     
        // and an ascii representation for those of us
        // that send text through the XBee
        Serial.println();
        for (int i= 0; i < rx.getDataLength(); i++){
          Serial.write(' ');
          if (iscntrl(rx.getData()[i]))
            Serial.write(' ');
          else
            Serial.write(rx.getData()[i]);
          Serial.write(' ');
        }
        Serial.println();
        // So, for example, you could do something like this:
        handleXbeeRxMessage(rx.getData(), rx.getDataLength());
        Serial.println();
      }
      else if (xbee.getResponse().getApiId() == ZB_IO_SAMPLE_RESPONSE) {
        xbee.getResponse().getZBRxIoSampleResponse(ioSample);
        Serial.print("Received I/O Sample from: ");
        // this is how you get the 64 bit address out of
        // the incoming packet so you know which device
        // it came from
        XBeeAddress64 senderLongAddress = ioSample.getRemoteAddress64();
        print32Bits(senderLongAddress.getMsb());
        Serial.print(" ");
        print32Bits(senderLongAddress.getLsb());
     
        // this is how to get the sender's
        // 16 bit address and show it
        // However, end devices that have sleep enabled
        // will change this value each time they wake up.
        uint16_t senderShortAddress = ioSample.getRemoteAddress16();
        Serial.print(" (");
        print16Bits(senderShortAddress);
        Serial.println(")");
        // Now, we have to deal with the data pins on the
        // remote XBee
        if (ioSample.containsAnalog()) {
          Serial.println("Sample contains analog data");
          // the bitmask shows which XBee pins are returning
          // analog data (see XBee documentation for description)
            uint8_t bitmask = ioSample.getAnalogMask();
            for (uint8_t x = 0; x < 8; x++){
            if ((bitmask & (1 << x)) != 0){
              Serial.print("position ");
              Serial.print(x, DEC);
              Serial.print(" value: ");
              Serial.print(ioSample.getAnalog(x));
              Serial.println();
            }
          }
        }
        // Now, we'll deal with the digital pins
        if (ioSample.containsDigital()) {
          Serial.println("Sample contains digtal data");
          // this bitmask is longer (16 bits) and you have to
          // retrieve it as Msb, Lsb and assemble it to get the
          // relevant pins.
          uint16_t bitmask = ioSample.getDigitalMaskMsb();
          bitmask <<= 8;  //shift the Msb into the proper position
          // and in the Lsb to give a 16 bit mask of pins
          // (once again see the Digi documentation for definition
          bitmask |= ioSample.getDigitalMaskLsb();
          // this loop is just like the one above, but covers all
          // 16 bits of the digital mask word.  Remember though,
          // not all the positions correspond to a pin on the XBee
          for (uint8_t x = 0; x < 16; x++){
            if ((bitmask & (1 << x)) != 0){
              Serial.print("position ");
              Serial.print(x, DEC);
              Serial.print(" value: ");
              // isDigitalOn takes values from 0-15
              // and returns an On-Off (high-low).
              Serial.print(ioSample.isDigitalOn(x), DEC);
              Serial.println();
            }
          }
        }
        Serial.println();
      }

      else {
        Serial.print("Got frame id: ");
        Serial.println(xbee.getResponse().getApiId(), HEX);
      }
    }
    else if (xbee.getResponse().isError()) {
      // some kind of error happened, I put the stars in so
      // it could easily be found
      Serial.print("************************************* error code:");
      Serial.println(xbee.getResponse().getErrorCode(),DEC);
    }
    else {
      // I hate else statements that don't have some kind
      // ending.  This is where you handle other things
    }
}

void handleXbeeRxMessage(uint8_t *data, uint8_t length){
  // this is just a stub to show how to get the data,
  // and is where you put your code to do something with
  // it.
  for (int i = 0; i < length; i++){
//    Serial.print(data[i]);
  }
//  Serial.println();
}

void showFrameData(){
  Serial.println("Incoming frame data:");
  for (int i = 0; i < xbee.getResponse().getFrameDataLength(); i++) {
    print8Bits(xbee.getResponse().getFrameData()[i]);
    Serial.print(' ');
  }
  Serial.println();
  for (int i= 0; i < xbee.getResponse().getFrameDataLength(); i++){
    Serial.write(' ');
    if (iscntrl(xbee.getResponse().getFrameData()[i]))
      Serial.write(' ');
    else
      Serial.write(xbee.getResponse().getFrameData()[i]);
    Serial.write(' ');
  }
  Serial.println();
}

// these routines are just to print the data with
// leading zeros and allow formatting such that it
// will be easy to read.
void print32Bits(uint32_t dw){
  print16Bits(dw >> 16);
  print16Bits(dw & 0xFFFF);
}

void print16Bits(uint16_t w){
  print8Bits(w >> 8);
  print8Bits(w & 0x00FF);
}

void print8Bits(byte c){
  uint8_t nibble = (c >> 4);
  if (nibble <= 9)
    Serial.write(nibble + 0x30);
  else
    Serial.write(nibble + 0x37);
     
  nibble = (uint8_t) (c & 0x0F);
  if (nibble <= 9)
    Serial.write(nibble + 0x30);
  else
    Serial.write(nibble + 0x37);
}